浙江萬能達爐業有限公司
手 機： 13705828806
電 話：0572-6871999 6087213 6870511
傳 真：0572-6087105
E-mail：1390003299@qq.com
地 址：浙江省長興縣林城工業園區鼎興北路6號（林城高速路口下20米左側）
- 2019-01-02 12:38:37
- 打印本文
- 關閉本頁
一、概況:
1、設備類型：
1噸塞棒底注式中頻保溫爐主要用于鋼（鐵）水的保溫和提溫，來自其它熔煉設備（如高爐、轉爐、沖天爐）的鋼（鐵）水，倒入保溫感應爐中，再微調成分，并適當提溫至最終澆鑄溫度。
二、設備主要技術參數
|
A、綜合參數 |
||
|
序號 |
項目 |
參數要求 |
|
1 |
設備形式 |
250kw |
|
2 |
額定容量 |
1T |
|
3 |
最大容量 |
1T+30% |
|
4 |
工作溫度 |
1450℃鑄鐵保溫 |
|
5 |
工作噪聲 |
<85分貝 |
|
6 |
爐體結構 |
鋼殼 |
|
7 |
出線方式 |
側出線 |
|
B、電氣參數: |
||
|
序號 |
項目 |
參數 |
|
1 |
電源功率 |
250kw /3相6脈1T |
|
2 |
整流項數 |
6脈 |
|
3 |
逆變器 |
SCR并聯逆變 |
|
4 |
額定頻率 |
1000Hz |
|
5 |
進線電壓 |
380V |
|
6 |
直流電壓 |
500V |
|
7 |
中頻電壓 |
750V |
|
8 |
啟動成功率 |
100% |
|
9 |
功率因數 |
0.92 |
|
C、配冷卻系統參數 |
||
|
序號 |
項目 |
參數 |
|
1 |
閉環冷卻塔 |
ZXZ-N80T（20/60)一體分層塔 |
|
2 |
冷卻塔殼體 |
鍍鋁鋅板 或304不銹鋼板 |
|
3 |
風機配套電機 |
1.1KW |
|
4 |
噴淋水泵 |
2.2KW |
|
5 |
主循環泵 |
7.5kw |
|
6 |
冷卻器 |
304冷卻器 |
|
D、爐體指標 |
||
|
序號 |
項目 |
參數 |
|
1 |
爐殼結構 |
鋼結構 |
|
2 |
磁軛材質 |
Z11-0.23 |
|
3 |
磁軛覆蓋率 |
85% |
|
4 |
磁軛夾緊 |
不銹鋼 1Cr18Ni9 |
|
5 |
磁軛散熱方式 |
雙水冷 |
|
6 |
感應器銅管材質 |
T2純銅99.9 |
|
感應圈內徑 |
900 壁厚5mm |
|
|
感應圈高度 |
500mm |
|
|
7 |
水路 |
4進4出 |
|
8 |
出線方式 |
側出 |
|
9 |
水冷圈材質 |
紫銅管 |
|
10 |
爐殼發熱量 |
＜75℃（爐底與爐蓋除外） |
|
11 |
絕緣 |
線圈與磁軛絕緣采用云母板雙層隔離 |
|
12 |
螺栓 |
普通碳鋼螺栓為8.8級。其他螺栓不銹鋼材質或銅制 |
|
13 |
坩堝模厚度 |
＞5mm |
|
14 |
水路連接軟管 |
采用無阻燃高絕緣橡膠管 |
|
15 |
集水器 |
不銹鋼材質 |
五、爐體結構描述:
5.1機械結構原理說明
爐體采用鋼殼磁軛爐體，金屬熔液的出口通道“澆口”設在電爐底部。(高鋁石墨質或氧化鋯質水口)由于金屬在熔煉過程中，雜質和熔渣均浮在液面；底注式澆注可避免雜質和熔渣進入鑄件型腔，大大減少?gòu)U品出現。 鋼水出口連接有塞桿動作機構；塞桿動作機構包括塞棒、氣缸和傳動杠桿，塞棒底部形狀與鋼水出口形狀相適配，且塞棒底部為由上至下漸縮形；氣缸驅動傳動杠桿沿一固定軸轉動，傳動杠桿帶動塞棒作上升或下降動作。用塞桿動作機構的上升或下降運動來控制出鋼口的開、關或開度，精確控制出鋼點和出鋼流量及出鋼流速，
塞桿動作機構包括塞棒2、氣缸3和傳動杠桿4，氣缸3連接傳動杠桿4的一端，氣缸的底部固定；塞棒2連接傳動杠桿4的另一端，塞棒2的底部形狀與鋼水出口形狀相適配，且塞棒2的底部為由上至下漸縮形；氣缸3驅動傳動杠桿4沿一固定軸轉動，傳動杠桿4帶動塞棒2作上升或下降動作。其特征在于鋼水出口橫截面為圓形，塞棒2的底部為圓椎形。傳動杠桿4的另一端固定連接有懸掛套管5，懸掛套管5用于將塞棒2懸掛于傳動杠桿4上。塞桿動作機構還包括旋轉軸承6，旋轉軸承6連接懸掛套管5和塞棒2之間。塞桿動作機構還包括支架7，支架7上固定連接有套筒型調正器(8)；還包括緩沖彈簧10和位置固定桿9，懸掛套管5的下端與緩沖彈簧10的上端固連，緩沖彈簧(10)的下端與旋轉軸承(6)的內圈固連，旋轉軸承6的外圈與位置固定桿(9)相連接。
title:
1 ton stopper bottom injection type intermediate frequency holding furnace
1 ton plug rod medium frequency holding furnace.cast tube special equipment
I. Overview:
1, equipment type:
The 1 ton stopper bottom injection type intermediate frequency holding furnace
is mainly used steel (iron) and raised temperature water insulation, steel (iron) melting water from other devices (such as blast furnace, converter, cupola), and poured into an induction furnace insulation, and then fine-tuning components, and provide appropriate Warm to the final casting temperature.
Second , the main technical parameters of the equipment
|
A, comprehensive parameters |
||
|
Serial number |
project |
Parameter requirement |
|
1 |
Equipment form |
250kw |
|
2 |
Rated Capacity |
1T |
|
3 |
Maximum capacity |
1T +30% |
|
4 |
Operating temperature |
1450 °C cast iron insulation |
|
5 |
Working noise |
<85 decibels |
|
6 |
Furnace structure |
Steel shell |
|
7 |
Way out |
Side outlet |
|
B, electrical parameters: |
||
|
Serial number |
project |
parameter |
|
1 |
Power supply |
250kw / 3 phase 6 pulse 1T |
|
2 |
Number of rectifiers |
6 veins |
|
3 |
Inverter |
SCR parallel inverter |
|
4 |
Rated frequency |
1000 Hz |
|
5 |
Line voltage |
380V |
|
6 |
DC voltage |
500V |
|
7 |
IF voltage |
750 V |
|
8 |
Start success rate |
100% |
|
9 |
Power factor |
0.92 |
|
C, with cooling system parameters |
||
|
Serial number |
project |
parameter |
|
1 |
Closed loop cooling tower |
ZXZ-N 80 T ( 20/60) integrated layered tower |
|
2 |
Cooling tower housing |
Galvanized or 304 stainless steel |
|
3 |
Fan supporting motor |
1.1KW |
|
4 |
Spray pump |
2.2 KW |
|
5 |
Main circulation pump |
7.5kw |
|
6 |
Cooler |
304 cooler |
|
D , furnace index |
||
|
Serial number |
project |
parameter |
|
1 |
Furnace shell structure |
Steel structure |
|
2 |
Yoke material |
Z11-0. 23 |
|
3 |
Yoke coverage |
8 5% |
|
4 |
Yoke clamping |
Stainless steel 1Cr18Ni9 |
|
5 |
Yoke cooling method |
Double water cooling |
|
6 |
Sensor copper tube material |
T2 pure copper 99.9 |
|
Induction ring inner diameter |
900 wall thickness 5 mm |
|
|
Induction loop height |
500 mm |
|
|
7 |
waterway |
4 in 4 out |
|
8 |
Way out |
Side out |
|
9 |
Water cooling ring material |
Copper tube |
|
10 |
Furnace shell heat |
<75 ° C (except the furnace bottom and the furnace cover) |
|
11 |
insulation |
The coil and the yoke are insulated by a double layer of mica board. |
|
12 |
bolt |
Ordinary carbon steel bolts are grade 8.8. Other bolts made of stainless steel or copper |
|
13 |
Die thickness |
>5mm |
|
14 |
Water connection hose |
Use non-flame retardant high insulation rubber tube |
|
15 |
Water collector |
Stainless steel |
Fifth , the furnace structure description:
5.1 mechanical principles described structure
The furnace body adopts a steel shell yoke furnace body, and the outlet channel "gate" of the metal melt is arranged at the bottom of the electric furnace. ( High-aluminum graphite or zirconia nozzle ) Since the metal is in the smelting process, impurities and slag float on the liquid surface; the bottom-injection casting can prevent impurities and slag from entering the casting cavity, greatly reducing the occurrence of waste. The steel water outlet is connected with a plug rod action mechanism; the plug rod action mechanism comprises a plug rod, a cylinder and a transmission lever, the bottom shape of the plug rod is adapted to the shape of the molten steel outlet, and the bottom of the plug rod is tapered from top to bottom; the cylinder drive transmission The lever rotates along a fixed axis, and the transmission lever drives the plug to raise or lower. Use the rising or falling movement of the plug rod action mechanism to control the opening, closing or opening of the taphole, and precisely control the tapping point and tapping flow rate and the tapping flow rate.
The plug rod action mechanism comprises a stopper rod 2, a cylinder 3 and a transmission lever 4, the cylinder 3 is connected to one end of the transmission lever 4, and the bottom of the cylinder is fixed ; the stopper rod 2 isconnected to the other end of the transmission lever 4, the bottom shape of the stopper rod 2 and the molten steel outlet The shape is adapted, and the bottom of the stopper rod 2 is tapered from top to bottom; the cylinder 3 drives the transmission lever 4 to rotate along a fixed axis, and the transmission lever 4 drives the stopper rod 2 to ascend or descend. It is characterized in that the steel water outlet has a circular cross section, and the bottom of the stopper rod 2 has a circular cone shape. The other end of the transmission lever 4 is fixedly connected with a suspension sleeve 5 for suspending the stopper rod 2 from the transmission lever 4. The stopper action mechanism further includes a rotary bearing 6 that connects between the suspension sleeve 5 and the stopper rod 2. The plug action mechanism further includes a bracket 7 to which the sleeve type adjuster (8) is fixedly coupled; a buffer spring 10 and a position fixing rod 9 are further fixed, and the lower end of the suspension sleeve 5 is fixed to the upper end of the buffer spring 10 The lower end of the buffer spring (10) is fixed to the inner ring of the rotary bearing (6), and the outer ring of the rotary bearing 6 is connected to the position fixing rod (9)
http://www.firstfurnace.com/BdwlkjProduct.asp?id=352
http://www.firstfurnace.com/BdwlkjProduct.asp?id=356
電 話：0572-6871999 手 機：13936361130 13705828806